C287 TCLK Interface/Timer - 2 channelC287 TCLK Interface/Timer - 2 channel
Available Documentation
[DUCAR.DOC]CMC287.VER R. J. DUCAR
11-11-91
CAMAC 287 Module - Detailed Listing of Implemented Versions
| Versions Directory | |||
|---|---|---|---|
| All Versions | Version 1.0 | Version 2.1 | Version 3.0 |
| Version 4.1 | Version 5.0 | Version 6.0 | Version 7.0 |
| Version 8.1 | Version 9.1 | Version 10.0 | Version 11.0 |
| Version 12.0 | Version 13.0 | Version 14.0 | |
All Versions:
The 287 module is a 279 module that has been modified to accept TCLK instead of a Beam Sync Clock as a primary input. The only hardware difference is different timing components on the 96S02 at IC location #25. PALs associated with the 279 module may often be used with implemented versions of the 287. Specifically: PALs 27905A.DAT and 27912A.DAT are common. PAL 27921A.DAT is also ex- pected to be common for nearly all versions of the 287, exception to which will be specifically noted. This PAL causes both channels of the 287 to be enabled upon power-up or module clear. The pro- grammable enable/disable feature is maintained. The four remaining PAL source files (28736x.DAT, 28737x.DAT, 28741x.DAT, and 28742x.DAT) are generally unique to each implemented version.
Version 1.0 TEST
This version of the 287 module is the form to which all con- structed modules are initially configured. The associated PALs are specifically programmed to accommodate manual and computer testing.
Channel 0: This channel is armed by an external trigger and outputs a pulse delayed from TCLK event $07.
Channel 1: This channel is armed by an external trigger and outputs a pulse delayed from TCLK event $07.
Module Location: Lab Test Stand
Unique PALs: 28736A.DAT, 27937A.DAT, 28741A.DAT, 28742A.DAT
DCE1 = DCE2 = DCE3 = $07 (720 Hz) DCE4 = $0F (15 Hz)
Notes: A normal testing environment is one in which TCLK is
applied to the front panel or 1R input. The TCLK 2R
output should be wired to the TCLK 4R input. The P2
output, 7R, should be wired to Ext Trig 0 and 1 inputs.
Version 2.1 Booster Chopper $12 + $13 Times 11-11-91
This version of the 287 module is installed in the Booster control system to provide coarse TCON and TCOFF times to the 200 MEV chopper only during a Booster beam cycle marked by TCLK events $12 and $13. Installation is made at the request of Curt Owen and Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK events $12 or $13. Parameter B:CTCB13 is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK events $12 or $13. Parameter B:CTCE13 is the assigned name for the delay value.
Module Location: $12 N1 (Booster)
Unique PALs: 28736B.DAT, 28741P.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $1D DCE4 = $13
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. Outputs from this module cable to 288 modules in slots 8 and 9 of the same crate to accommodate fine delays of 0 to 90 nanoseconds in 10 nanosecond steps.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 3.0
This version of the 287 module is installed in the Booster control system to provide coarse TCON and TCOFF times to the 200 MEV chopper only during a Booster beam cycle marked by TCLK event $14. Installation is made at the request of Curt Owen and Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK event $14. Parameter B:CTCB14 is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $14. Parameter B:CTCE14 is the assigned name for the delay value.
Module Location: $12 N2 (Booster)
Unique PALs: 28736C.DAT, 28741C.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $1D DCE4 = $14
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. Outputs from this module cable to 288 modules in slots 8 and 9 of the same crate to accommodate fine delays of 0 to 90 nanoseconds in 10 nanosecond steps.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 4.1
This version of the 287 module is installed in the Booster control system to provide coarse TCON and TCOFF times to the 200 MEV chopper only during a Booster beam cycle marked by TCLK events $15. Installation is made at the request of Curt Owen and Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK event $15. Parameter B:CTCB15 is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $15. Parameter B:CTCE15 is the assigned name for the delay value.
Module Location: $12 N3 (Booster)
Unique PALs: 28736J.DAT, 28741J.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $1D DCE4 = $15
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. Outputs from this module cable to 288 modules in slots 8 and 9 of the same crate to accommodate fine delays of 0 to 90 nanoseconds in 10 nanosecond steps.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 5.0
This version of the 287 module is installed in the Booster control system to provide coarse TCON and TCOFF times to the 200 MEV chopper only during a Booster beam cycle marked by TCLK event $16. Installation is made at the request of Curt Owen and Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK event $16. Parameter B:CTCB16 is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $16. Parameter B:CTCE16 is the assigned name for the delay value.
Module Location: $12 N4 (Booster)
Unique PALs: 28736E.DAT, 28741E.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $1D DCE4 = $16
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. Outputs from this module cable to 288 modules in slots 8 and 9 of the same crate to accommodate fine delays of 0 to 90 nanoseconds in 10 nanosecond steps.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 6.0
This version of the 287 module is installed in the Booster control system to provide coarse TCON and TCOFF times to the 200 MEV chopper only during a Booster beam cycle marked by TCLK event $17. Installation is made at the request of Curt Owen and Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK event $17. Parameter B:CTCB17 is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $17. Parameter B:CTCE17 is the assigned name for the delay value.
Module Location: $12 N5 (Booster)
Unique PALs: 28736F.DAT, 28741F.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $1D DCE4 = $17
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. Outputs from this module cable to 288 modules in slots 8 and 9 of the same crate to accommodate fine delays of 0 to 90 nanoseconds in 10 nanosecond steps.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 7.0
This version of the 287 module is installed in the Booster control system to provide triggers for the Orbump Power Supply. Installation is made at the request of Curt Owen and Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK events $12 and $13. Parameter B:TORB13 is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $14. Parameter B:TORB14 is the assigned name for the delay value.
Module Location: $30 N14 (Booster)
Unique PALs: 28736G.DAT, 28741G.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $1D DCE3 = $12 + $13 DCE4 = $14
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. Outputs from this module are wire-or'd with the outputs from slots N15 and N16 and with the Channel 0 output from slot N17.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 8.1
This version of the 287 module is installed in the Booster control system to provide triggers for the Orbump Power Supply. Installation is made at the request of Curt Owen and Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK event $15. Parameter B:TORB15 is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $16. Parameter B:TORB16 is the assigned name for the delay value.
Module Location: $30 N15 (Booster)
Unique PALs: 28736M.DAT, 28741M.DAT, 28742B.DAT
DCE1 = $12 DCE2 = $1D DCE3 = $15 DCE4 = $16
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. Outputs from this module are wire-or'd with the outputs from slots N14 and N16 and with the Channel 0 output from slot N17.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 9.1
This version of the 287 module is installed in the Booster control system to provide triggers for the Orbump Power Supply. Installation is made at the request of Curt Owen and Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK event $17. Parameter B:TORB17 is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $19. Parameter B:TORB19 is the assigned name for the delay value.
Module Location: $30 N16 (Booster)
Unique PALs: 28736N.DAT, 28741N.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $17 DCE4 = $19
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. The Channel 0 output from this module is wire-or'd with the outputs from slots N14 and N15 and with the Channel 0 output from slot 17.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 10.0
This version of the 287 module is installed in the Booster Control System to provide 100 nsec resolution timing for wire scanners. Installation is being made at the request of Jim Lackey. Both channels are used and are wire-or'd together. Channel 0 is normally enabled and provides fine timing at the beginning of a Booster Beam Cycle. Channel 1 is normally disabled and is referenced to a 177 timing channel. This channel provides fine timing later in a Booster Beam Cycle. On the infrequent occasions when Channel 1 is utilized, Channel 0 should be disabled.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK events $13 + $14 + $15 + $16 + $17 + $19 + $1C. Maximum delay on this channel is 6.5535 msec. Parameter B:TWIRE is assigned to the delay value. Upon power-up, this channel is normally enabled.
Channel 1: This channel is always armed and outputs a pulse delayed from an externally applied pulse. This pulse is sourced from a 177 timing channel B:TWIREC at $12 N20 A(1) and is applied the External Trig 1 Input of the 287 module. Parameter B:TWIREF is assigned to the delay value. B:TIREC is normally referenced to TCLK event $10. Upon power-up, this channel is normally disabled.
Module Location: $12 N19 (Booster)
Unique PALs: 28721A.DAT, 28736I.DAT, 27937H.DAT, 28741I.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $1D
DCE4 = $13 + $14 + $15 + $16 + $17 + $19 + $1C
Notes: There is presently no need for ICs at locations 16, 26, 32, and 65.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
37-15 is patched to 41-11. Channels 0 and 1 are wire- or'd at the I/O connector.
Version 11.0
This version of the 287 module is installed in the Booster control system to provide coarse TCON and TCOFF times to the 200 MEV chopper only during a Booster beam cycle marked by TCLK events $19. Installation is made at the request of Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK event $19. Parameter B:CTCB19 is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $19. Parameter B:CTCE19 is the assigned name for the delay value.
Module Location: $12 N6 (Booster)
Unique PALs: 28736K.DAT, 28741K.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $1D DCE4 = $19
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. Outputs from this module cable to 288 modules in slots 8 and 9 of the same crate to accommodate fine delays of 0 to 90 nanoseconds in 10 nanosecond steps.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 12.0
This version of the 287 module is installed in the Booster control system to provide coarse TCON and TCOFF times to the 200 MEV chopper only during a Booster beam cycle marked by TCLK events $1C. Installation is made at the request of Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK event $1C. Parameter B:CTCB1C is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $1C. Parameter B:CTCE1C is the assigned name for the delay value.
Module Location: $12 N7 (Booster)
Unique PALs: 28736L.DAT, 28741L.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $1D DCE4 = $1C
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. Outputs from this module cable to 288 modules in slots 8 and 9 of the same crate to accommodate fine delays of 0 to 90 nanoseconds in 10 nanosecond steps.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 13.0
This version of the 287 module is installed in the Booster control system to provide triggers for the Orbump Power Supply. Installation is made at the request of Jim Lackey.
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK event $1C. Parameter B:TORB1C is the assigned name for the delay value.
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $1C. There is no assigned parameter name for the delay value.
Module Location: $30 N17 (Booster)
Unique PALs: 28736L.DAT, 28741L.DAT, 28742B.DAT
DCE1 = $11 DCE2 = $12 DCE3 = $1D DCE4 = $1C
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65. The Channel 0 output from this module is wire-or'd with the outputs from slots N14, N15, and N16.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
Version 14.0
This version of the 287 module is installed in the
Channel 0: This channel is always armed and outputs a pulse delayed from TCLK events $
Channel 1: This channel is always armed and outputs a pulse delayed from TCLK event $
Module Location: $ N
Unique PALs: 28736 .DAT, 28741 .DAT, 28742 .DAT
DCE1 = $ DCE2 = $ DCE3 = $ DCE4 = $
Notes: There is presently no need for ICs at locations 9, 10, 16, 26, 32, 37, and 65.
The maximum delay of these channels is 6.5535 millisec- onds with a least count resolution of 100 nanoseconds.
PALS DOCUMENTATION
module 28721a title ' CAMAC 287 V10.0 R. J. DUCAR 8-20-86 ' 28721a device 'f153';
COM, NC2, NC3, NC4, CLR pin 1,2,3,4,5; DF16S, DF2426S, F2, A1 pin 6,7,8,9; DF160S, NC12, CH1EN, CH0EN, DF161S pin 11,12,13,14,15; CH1ENB, CH0ENB, NC18, NC19 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DF160S = /DF16S*A1*CLR + /CLR
CH1EN = /DF2426S*/F2*/A1*CLR + /CH1ENB
CH0EN = /DF2426S*/F2*A1*CLR + /CLR + /CH0ENB
/DF161S = /DF16S*/A1*CLR + /CLR
CH1ENB = /DF2426S*F2*/A1*CLR + /CLR + /CH1EN
CH0ENB = /DF2426S*F2*A1*CLR + /CH0EN
"DESCRIPTION: This PAL provides the third level of NAF decoding
for the CAMAC 287 module. This version provides
programmable enable/disable capability for both
timing channels. Channel 0 is enabled and Channel
1 is disabled when the module is powered up or
cleared by the Z*S2 or F(9)A(0) operations.
end 28721a
module 28736a title ' CAMAC 287 V1.0 TEST R. DUCAR 6-3-84 ' 28736a device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0 ;
/DCE2 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0 ;
/DCE3 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0 ;
/DCE4 = /ED*/B7*/B6*/B5*/B4*B3*B2*B1*B0 ;
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module V1.0 which is the initial test version of all 287 modules.
For this PAL: DCE1 = $07 (720 Hz)
DCE2 = $07 (720 Hz)
DCE3 = $07 (720 Hz)
DCE4 = $0F (15 Hz)
end 28736a
module 28736b title ' CAMAC 287 V2.0 R. DUCAR 6-3-84 ' 28736b device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;
/DCE3 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*B0 ;
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 2.0.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $1D
DCE4 = $13
end 28736b
module 28736c title ' CAMAC 287 V3.0 R. DUCAR 6-3-84 ' 28736c device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;
/DCE3 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*/B0 ;
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 3.0.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $1D
DCE4 = $14
end 28736c
module 28736d title ' OBSOLETE 3-15-88 287 ' 28736d device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;
/DCE3 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0 +
/ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0 +
/ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0 ;
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 4.0.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $1D
DCE4 = $15 + $19 + $1C
end 28736d
module 28736e title ' CAMAC 287 V5.0 R. DUCAR 6-3-84 ' 28736e device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;
/DCE3 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*/B0 ;
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 5.0.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $1D
DCE4 = $16
end 28736e
module 28736f title ' CAMAC 287 V6.0 R. DUCAR 6-3-84 ' 28736f device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;
/DCE3 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*B0 ;
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 6.0.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $1D
DCE4 = $17
end 28736f
module 28736g title ' CAMAC 287 V7.0 R. DUCAR 7-2-84 ' 28736g device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;
/DCE2 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;
/DCE3 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 +
/ED*/B7*/B6*/B5*B4*/B3*/B2*B1*B0 ;
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*/B0 ;
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 7.0.
For this PAL: DCE1 = $11
DCE2 = $1D
DCE3 = $12 + $13
DCE4 = $14
end 28736g
module 28736h title ' OBSOLETE 3-15-88 287 ' 28736h device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;
/DCE2 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;
/DCE3 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0 +
/ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0 +
/ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0 ;
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*/B0 ;
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 8.0.
For this PAL: DCE1 = $12
DCE2 = $1D
DCE3 = $15 + $19 + $1C
DCE4 = $16
end 28736h
module 28736i title ' CAMAC 287 V10.0 R. J. DUCAR 8-20-86 ' 28736i device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;"11
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;"12
/DCE3 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;"1D
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*B0 + "13
/ED*/B7*/B6*/B5*B4*/B3*B2 + "14 15 16 17
/ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0 + "19
/ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0 ;"1C
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 10.0.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $1D
DCE4 = $13 + $14 + $15 + $16 + $17 + $19 + $1C
end 28736i
module 28736j title ' CAMAC 287 V4.1 R. DUCAR 3-14-88 ' 28736j device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;"11
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;"12
/DCE3 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;"1D
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0 ;"15
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 4.1.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $1D
DCE4 = $15
end 28736j
module 28736k title ' CAMAC 287 V11.0 R. DUCAR 3-14-88 ' 28736k device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;"11
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;"12
/DCE3 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;"1D
/DCE4 = /ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0 ;"19
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 11.0.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $1D
DCE4 = $19
end 28736k
module 28736l title ' CAMAC 287 V12.0 R. DUCAR 3-14-88 ' 28736l device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;"11
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;"12
/DCE3 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;"1D
/DCE4 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0 ;"1C
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 12.0.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $1D
DCE4 = $1C
end 28736l
module 28736m title ' CAMAC 287 V8.1 R. DUCAR 3-15-88 ' 28736m device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;"11
/DCE2 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*B0 ;"1D
/DCE3 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0 ;"15
/DCE4 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*/B0 ;"16
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 8.1.
For this PAL: DCE1 = $12
DCE2 = $1D
DCE3 = $15
DCE4 = $16
end 28736m
module 28736n title ' CAMAC 287 V9.1 R. DUCAR 3-15-88 ' 28736n device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; NC11, DCE4, NC13, DCE3, NC15 pin 11,12,13,14,15; DCE1, NC17, NC18, DCE2 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/DCE1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*/B1*B0 ;"11
/DCE2 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0 ;"12
/DCE3 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*B0 ;"17
/DCE4 = /ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0 ;"19
"DESCRIPTION: This PAL decodes any combination of events on TCLK for the DCE1 through DCE4 front panel out- puts. This PAL is unique for 287 module Ver- sion 9.1.
For this PAL: DCE1 = $11
DCE2 = $12
DCE3 = $17
DCE4 = $19
end 28736n
module 28741a title ' CAMAC 287 V1.0 TEST R. DUCAR 6-4-85 ' 28741a device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
/P2 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0 ;
/T5 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0 ;
/T6 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0 ;
/T7 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0 ;
/T8 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0 ;
R0 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0*ARM0;
R1 = /ED*/B7*/B6*/B5*/B4*/B3*B2*B1*B0*ARM1;
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides up to four separate outputs
to the PAL at location 42. It also provides the
reference resets to both of the 287 timing chan-
nels. P2 may be defined as an input or output.
P2 may be connected to P1 of the PAL at location
37 by addition of a hard wired jumper. This PAL
is unique and is programmed for the initial test
version of all 287 modules, Version 1.0.
For this PAL: P2 = $07 (720 Hz)
T5 = $07
T6 = $07
T7 = $07
T8 = $07
R0 = $07 * ARM0
R1 = $07 * ARM1
end 28741a
module 28741b title ' CAMAC 287 V2.0 R. DUCAR 6-4-85 ' 28741b device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*B0*ARM0;
R1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*B0*ARM1;
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 2.0.
For this PAL: R0 = $13 * ARM0
R1 = $13 * ARM1
**** This PAL is obsolete as of 11-12-91. ****
end 28741b
module 28741c title ' CAMAC 287 V3.0 R. DUCAR 6-4-85 ' 28741c device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*/B0*ARM0;
R1 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*/B0*ARM1;
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 3.0.
For this PAL: R0 = $14 * ARM0
R1 = $14 * ARM1
end 28741c
module 28741d title ' OBSOLETE 3-15-88 287 ' 28741d device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0*ARM0 +
/ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0*ARM0 +
/ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0*ARM0 ;
R1 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0*ARM1 +
/ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0*ARM1 +
/ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0*ARM1 ;
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 4.0.
For this PAL: R0 = ($15 + $19 + $1C) * ARM0
R1 = ($15 + $19 + $1C) * ARM1
end 28741d
module 28741e title ' CAMAC 287 V5.0 R. DUCAR 6-4-85 ' 28741e device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*/B0*ARM0;
R1 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*/B0*ARM1;
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 5.0.
For this PAL: R0 = $16 * ARM0
R1 = $16 * ARM1
end 28741e
module 28741f title ' CAMAC 287 V6.0 R. DUCAR 6-4-85 ' 28741f device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*B0*ARM0;
R1 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*B0*ARM1;
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 6.0.
For this PAL: R0 = $17 * ARM0
R1 = $17 * ARM1
end 28741f
module 28741g title ' CAMAC 287 V7.0 R. DUCAR 7-2-85 ' 28741g device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0*ARM0 +
/ED*/B7*/B6*/B5*B4*/B3*/B2*B1*B0*ARM0;
R1 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*/B0*ARM1;
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 7.0.
For this PAL: R0 = ($12 + $13) * ARM0
R1 = $14 * ARM1
end 28741g
module 28741h title ' OBSOLETE 3-15-88 287 ' 28741h device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0*ARM0 +
/ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0*ARM0 +
/ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0*ARM0 ;
R1 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*/B0*ARM1 ;
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 8.0.
For this PAL: R0 = ($15 + $19 + $1C) * ARM0
R1 = $16 * ARM1
end 28741h
module 28741i title ' CAMAC 287 V10.0 R. J. DUCAR 8-20-86 ' 28741i device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*B0*ARM0 + "13
/ED*/B7*/B6*/B5*B4*/B3*B2*ARM0 + "14 15 16 17
/ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0*ARM0 + "19
/ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0*ARM0 ;"1C
R1 = /P2*ARM1 ;
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 10.0.
For this PAL: R0 = ($13 + $14 + $15 + $16 +
$17 + $19 + $1C) * ARM0
R1 = P2 * ARM1 where P2 correlates
to Ext Trig 1 Input.
end 28741i
module 28741j title ' CAMAC 287 V4.1 R. DUCAR 3-14-88 ' 28741j device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0*ARM0 ;"15
R1 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0*ARM1 ;"15
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 4.1.
For this PAL: R0 = $15 * ARM0
R1 = $15 * ARM1
end 28741j
module 28741k title ' CAMAC 287 V11.0 R. DUCAR 3-14-88 ' 28741k device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0*ARM0 ;"19
R1 = /ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0*ARM1 ;"19
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 11.0.
For this PAL: R0 = $19 * ARM0
R1 = $19 * ARM1
end 28741k
module 28741l title ' CAMAC 287 V12.0 R. DUCAR 3-14-88 ' 28741l device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0*ARM0 ;"1C
R1 = /ED*/B7*/B6*/B5*B4*B3*B2*/B1*/B0*ARM1 ;"1C
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 12.0.
For this PAL: R0 = $1C * ARM0
R1 = $1C * ARM1
end 28741l
module 28741m title ' CAMAC 287 V8.1 R. DUCAR 3-15-88 ' 28741m device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*B2*/B1*B0*ARM0 ;"15
R1 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*/B0*ARM1 ;"16
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 8.1.
For this PAL: R0 = $15 * ARM0
R1 = $16 * ARM1
end 28741m
module 28741n title ' CAMAC 287 V9.1 R. DUCAR 3-15-88 ' 28741n device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*B2*B1*B0*ARM0 ;"17
R1 = /ED*/B7*/B6*/B5*B4*B3*/B2*/B1*B0*ARM1 ;"19
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 9.1.
For this PAL: R0 = $17 * ARM0
R1 = $19 * ARM1
end 28741n
module 28741p title ' CAMAC 287 V2.1 R. DUCAR 11-11-91 ' 28741p device 'f153';
B0, B1, B2, B3, B4 pin 1,2,3,4,5; ED, B5, B6, B7 pin 6,7,8,9; P2, T5, T6, T7, T8 pin 11,12,13,14,15; ARM0, ARM1, R0, R1 pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
R0 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0*ARM0 + " $12
/ED*/B7*/B6*/B5*B4*/B3*/B2*B1*B0*ARM0 ;" $13
R1 = /ED*/B7*/B6*/B5*B4*/B3*/B2*B1*/B0*ARM1 + " $12
/ED*/B7*/B6*/B5*B4*/B3*/B2*B1*B0*ARM1 ;" $13
"DESCRIPTION: This PAL decodes TCLK events for the CAMAC 287
module. It provides the reference resets to
both of the 287 timing channels. This PAL is
unique and is programmed for Version 2.1.
For this PAL: R0 = [$12 + $13] * ARM0
R1 = [$12 + $13] * ARM1
$12 Pre-Pulse added to equations on 11-11-91. end 28741p
module 28742a title ' CAMAC 287 V1.0 TEST R. DUCAR 6-4-85 ' 28742a device 'f153';
T5, T6, T7, T8, T4 pin 1,2,3,4,5; T3, T2, T1, CLR pin 6,7,8,9; RF1, RF0, NC13, CH1EN, CH0EN pin 11,12,13,14,15; A0S, A1S, A0R, A1R pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
A0S = /T1*CH0EN*CLR;
/A0R = /RF0 + /CH0EN
A1S = /T2*CH1EN*CLR;
/A1R = /RF1 + /CH1EN
"DESCRIPTION: This PAL provided set and reset control for
the ARM flip flops for channels zero and one.
This PAL is unique and is programmed for the
initial test version of all 287 modules, V1.0.
end 28742a
module 28742b title ' CAMAC 287 V2.0, V3.0, V4.0, V5.0, V6.0 R. DUCAR 6-4-85 ' 28742b device 'f153';
T5, T6, T7, T8, T4 pin 1,2,3,4,5; T3, T2, T1, CLR pin 6,7,8,9; RF1, RF0, NC13, CH1EN, CH0EN pin 11,12,13,14,15; A0S, A1S, A0R, A1R pin 16,17,18,19;
H,L,X,Z = 1,0,.X.,.Z.; "Use standard PALASM operators @ALTERNATE equations
A0S = CH0EN*CLR;
/A0R = /CH0EN ;
A1S = CH1EN*CLR;
/A1R = /CH1EN ;
"DESCRIPTION: This PAL provided set and reset control for
the ARM flip flops for channels zero and one.
This PAL is unique and is programmed for V2.0,
V3.0, V4.0, V5.0, and V6.0 of the 287 module.
end 28742b